Table of Content
The Xbox Series X/S and One X/S controllers use AA batteries, but you can get a charging stand that includes compatible rechargeable batteries. Depending on your home theater setup, get an appropriate box, basket, or drawer. If you don't mind having a bit of fuzziness on the undersides of your remotes, you can use Velcro strips with double-sided adhesive to keep your remotes in place. Magnets are another option, but only if you aren't keeping the remotes close to the TV; even then, make sure the magnets aren't too strong. Make sure the cables are rated for 4K60 at the very least .
Untidy wires can ruin your home theater appearance and even cause accidents. To avoid any of these issues, you should properly manage all your speaker wires, media cables, TV cables, and power cables. These adhesives can also hold a cable bundle running from a wall-mounted TV flat against the wall for a neater appearance. You can also use them to fasten wires and wire bundles to the back of your A/V cabinet. The In-Wall TV Power Kit is pre-wired to simplify installation and easily hides power and AV cabling inside the wall cavity without modifying electrical wiring. There are ways in which you can organize your cabling to better help you identify and isolate your equipment from any interference .
Electrical Supplies
After installing your studs, you can mount the rail molding to the wall firmly. The molds need to be cut perfectly to fit each other precisely at each end. To install these wires, you will need to stick the adhesive side to the wall which will leave the paintable side exposed. You can then paint over the wires to make them blend in for invisible concealment.
Since so many devices have plugs that are often slightly too large to work next to each other, don't assume you can fit everything on a single row of outlets. This doesn't mean you should daisy-chain power strips, though . Otherwise, you're tempting both your circuit breakers and all reasonable fire safety. Tie the power and AV cables separately to reduce electromagnetic interference then cut off the excess ties. After this, use adhesive pads or clamps to attach the cables to the cabinet or rack for a cleaner look. Super-slim speaker wires are flat wires that are mainly 16-gauge wires with 2 or 4 conductors.
Cable Management Tip #1: Keep Power Separate from Audio & Video
Once secured, you can then zip tie the bundle to the anchor point and direct your wires into controllable paths that keep everything nice and neat. There’s nothing worse than having to trace out speakers because some installer forgot to label the speaker cables…except when that installer is me. I can’t tally how many times I’ve nailed myself with this in the past.
Most home entertainment devices come with HDMI cables, but they might not be the best for your setup. Obviously they're useless if they're too short, but if they're too long, they dangle and add to the clutter behind your TV. Tired of tangled cables and piles of remotes cluttering your living room or home theater? These inexpensive products help you keep everything neat and organized for a professional, streamlined look. You will need to make sure that the cover or raceway you are buying is big enough to run a bundle of wires. However, you may need to buy wires and cables that are longer than the intended length in case you need to do any modifications to your system.
Label Your Wires…in Multiple Places
Conceal unsightly cables, get power where you need it, all for a clean, professional look. Explore home theater, power, and cable management solutions. Adhesive backed cord clips hold a single cord or cable firmly in any desired route. Cable retaining clips are useful for other applications, such as wiring for stereo, telephone, etc... Thick, strong retaining arm with round contour holds larger cords, cables or wire bundles. Take your dinky single-row power strip and throw it in the trash.
These speaker wires are mainly low-voltage wires that come in different varieties. You will also need flat speaker wire terminals pairs for each speaker if you decide to use this option. Cable raceways/covers/ducts can be used to hide your speaker wires. Pass-throughs for powered cables that have slots for running both the power cables and media cables.
Go wireless
They can be plastic zip ties or Velcro strips, or if you want to be extra neat you can use entire sleeves for your cable groups. If your home theater components are close together, use these to keep them organized. If you aren't using a sleeve, place a cable tie every foot or so on groups of cables that run near each other. As each cable terminates at its device, let it run free while you secure the rest of the bundle running down the line. This will turn your big nest of wires into a tree trunk instead, with individual branches running off to each device connected to your TV. While I advocate for having extra length on long-run wires, interconnects are a place I like to match my gear up pretty tightly.
Even without in-wall or in-ceiling speakers, you can still fish the speaker wires after cutting holes where you can run the wires through. You can then install grommets/plates/junction boxes at the hole cuttings where the ends of the speaker wires will pass through. For a bundle of speaker wires, tie them together using wire ties then attach them to your walls’ moldings using adhesive pads or cable clamps. Another way to hide TV cables on a wall-mounted TV and prevent them from dangling is by using customizable raceway kits or cord covers.
Most rooms will have baseboards with spaces between them and the floor for carpeting. You can use a stir stick or ruler to tuck your speaker wires between the carpets and baseboards. If your TV is wall-mounted, you can install an on-wall cable channel to feed the cables to the TV. You will only need to use a screwdriver to secure it to the wall and a hacksaw to cut it to the right length. When you are dealing with a lot of cables and wires it is always important to label all of them to avoid any confusion later on by knowing where all the cables are running to. Not too much problem going to optical instead of 2 heavy RCA cables and HDMI.
This can result in a tangled nest of cables behind your TV, in your cabinet, or scattered around your living room. When using flat speaker wires, you can leave the plug terminals exposed at the ends or use junction boxes to add better style. You can buy some color-coded labels for your speaker wires and the rest of the cables but you also have the option of making your DIY labels using a marker and masking tape. Wire labels do not cost much and can be bought from your local stores or online for cheap. This low profile raceway is an elegant way of hiding your home theater cables in your home while blending beautifully into your interior decorations.
By all means, make up your own scheme, but if you do this ahead of time, you’ll be able to recognize the cable ends 5y from now if needed. In-Wall Power Power where you need it, you just cant see it. Cable Turtle Part of the Museum of Modern Art’s Design Collection, the Cable Turtle wraps up excess cable length, and stores it out of sight in its sleek shell. Make sure to check out our story on how to clean up messy cables everywhere else in your home, too. However, you should note that going fully wireless is more expensive.
Good cable management is possible and, if you're willing to plan, you can keep the back of your TV free of clutter. You might have to buy some bits and bobs to rein everything in, but the accessories we mention here are pretty cheap. You will also have a lot of flexibility when it comes to where you can place your speakers and other devices without having to worry about the length of the cables. You can also run the speaker wires through the corners of the floor under the carpeting if they are too thick.
When you’re wiring up your home theater, don’t get confused by all of the options available to you. In no particular order, here are a few of our favorite tricks and techniques that cover anything from wiring up speakers, to handling interconnects. The Flex Tubing Cable Organizer is a plastic corrugated split tubing. It is manufactured in different sizes ranging from 1/4" i.d. to 2" (the home theater kit includes both ½” and 1” wireloom). Our tubing offers excellent protection for wiring harnesses, cables, tubing and hoses. It is very light in weight, has excellent flexibility and provides protection from abrasion, puncture, vibration and friction.
You can also repaint the cable concealer to match the color of your wall for a seamless blend. This is why planning your home theater and knowing where everything is going to be placed is very important. Not all your devices will use cables of the same length but depending on where you are placing your devices, you can invest in cables that are neither too short nor too long.
No comments:
Post a Comment